Have you been looking for related information about How to Install a Bathtub?
Setting up a bath tub isn't exactly rocket science, yet it does call for solid plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately challenging job. If the old tub is readily available, the project can move easily; if you have to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the task and also fit attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub and also don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist need to consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome because of the restricted accessibility that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Secure the faucet in place with the producer supplied backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Using the two wood boards under its feet, place the tub in the called for setting. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the tub up until the level reviews level.
To set up faucets, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and inspect all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill up the tub and likewise inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub should wait until the tub has actually been utilized a minimum of when as this will certainly resolve it right into its last placement.
Planning for the Installation
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, causing the water to pass through the wall surface between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can split fairly early if you do not take into account this motion before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly readily available on the market. It is advisable to fit the ceramic tiles using water-resistant or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you liked the post. If you appreciated our article kindly make sure you remember to pass it around. I am grateful for your time. Please stop by our website back soon.
Contact